A chiller in a Denver building was usually set before the walls closed around it. Getting the old one out and the new one in means a route through a mechanical room, a basement, or a roof — and often a crane on a city street. We plan and rig HVAC equipment across the Denver metro, from the first opening to the last anchor bolt.
Quick answer: Badass Logistics provides chiller, boiler & HVAC rigging in Denver, CO and the surrounding metro. We rig chillers, boilers, cooling towers, air handlers, and rooftop units into and out of mechanical rooms, basements, penthouses, and roofs — sectioned where the opening demands it and set ready for the mechanical contractor. Our crews work across Denver and nearby Colorado metros, and moves between facilities run as project freight under the same plan — usually quoted the same day. Call (307) 284-1332.
The machine is rarely the hard part of an HVAC replacement. The route is. A centrifugal chiller headed for a basement plant room, a boiler that only fits through a wall, a cooling tower that has to go up past occupied floors — the plan is set by doors, corridors, slab capacity, and crane reach long before it is set by the unit. In Denver, much of that work is in buildings that cannot shut down while it happens.
Badass Logistics walks both routes — the old unit's way out and the new unit's way in — and rigs them as one job. Refrigerant recovery, electrical disconnects, and piping stay with your licensed mechanical contractor; we sequence around them. Units are skated, jacked, or sectioned at factory joints where the builder allows it, and roof work runs as a planned crane lift. How to move a boiler or chiller →
Large HVAC plant in Denver is concentrated in campuses that run around the clock. The metro's hospitals — UCHealth University of Colorado Hospital, Denver Health Medical Center, and National Jewish Health — replace chillers and boilers without ever closing a wing. CU Anschutz Medical Campus and University of Colorado Boulder run central plants of their own, often in basements reached by one freight elevator or a single knockout wall.
Denver, CO runs on energy & construction equipment, and almost none of it stays put. Same crews and the same chiller and HVAC rigging standards across the region:
Downtown and Tech Center office towers, the Anschutz Medical Campus, and Denver International Airport carry large central plant. The equipment we rig for them includes:
On the industrial side, Denver's plants are a mix of century-old brick and heavy-timber industrial buildings in the Globeville and Elyria-Swansea corridor with rail spurs and narrow bays, and newer clear-span distribution buildings along the I-70 and I-76 corridors, and process cooling there means chillers, towers, and air handlers set on mezzanines and roofs. That work concentrates in the Waterton Canyon aerospace campus in Jefferson County, the Centennial Airport aerospace corridor in Arapahoe County, the Commerce City refining and rail district north of downtown, and the Globeville and Elyria-Swansea industrial corridor along the South Platte River.
Centrifugal, screw, and absorption chillers rigged out of and into plant rooms across the Denver metro.
Fire-tube and water-tube boilers removed and set, sectioned where the opening demands it across the Denver metro.
RTUs, cooling towers, and condensers lifted onto and off roofs across the Denver metro.
AHUs and fan sections moved through buildings and set on curbs and pads across the Denver metro.
Plenty of Denver jobs start and finish on one floor. The rest have to travel — to a new building across the metro, a sister plant down I-25, I-70 and I-76, or a facility in another state. We don't hand that part off. It runs as project freight inside the same plan: machines crated or prepped on site, loads sequenced to the rig-out, transport through our licensed broker and carrier partners with dedicated capacity for bigger moves, and our crew waiting at the destination to set it.
Data centers are the other big buyer of cooling plant in Denver. CoreSite Denver campus and Flexential Denver data centers run chillers, CRAH units, and condensers that are replaced and added on the facility's schedule, not the weather's.
Every chiller, boiler & HVAC rigging job in Denver, CO is quoted from the actual work, not a rate sheet. These are the things that move the number — send them with your request and you'll get a real quote back fast:
Photos of the equipment, its nameplate, and the path out of the building save a site visit on smaller Denver jobs. For bigger moves we walk both sites before we price anything.
The same Denver crews handle every kind of industrial rigging. If your job looks more like one of these, start here:
Running a trucking fleet out of Denver? See truck dispatch for fleets of 4+ trucks.
Working throughout Denver, CO and the surrounding metro — backed by a nationwide network of 88 locations when a move crosses state lines.
Chiller, Boiler & HVAC Rigging throughout Denver and the industrial suburbs around it — the towns below are where the plants, shops and distribution parks actually sit:
| Town | County | From downtown |
|---|---|---|
| Aurora | Adams County | 8 mi |
| Lakewood | Jefferson County | 6 mi |
| Commerce City | Adams County | 6 mi |
| Thornton | Adams County | 9 mi |
| Westminster | Adams County | 7 mi |
| Arvada | Jefferson County | 7 mi |
| Centennial | Arapahoe County | 13 mi |
| Brighton | Adams County | 19 mi |
| Golden | Jefferson County | 13 mi |
| Boulder | Boulder County | 24 mi |
| Greeley | Weld County | 50 mi |
| Highlands Ranch | Douglas County | 13 mi |
| Longmont | Boulder County | 30 mi |
| Loveland | Larimer County | 46 mi |
| Broomfield | Broomfield County | 14 mi |
| Castle Rock | Douglas County | 26 mi |
| Parker | Douglas County | 19 mi |
| Littleton | Arapahoe County | 9 mi |
| Northglenn | Adams County | 10 mi |
| Dakota Ridge | Jefferson County | 12 mi |
| Englewood | Arapahoe County | 6 mi |
| Ken Caryl | Jefferson County | 13 mi |
| Wheat Ridge | Jefferson County | 5 mi |
| Lafayette | Boulder County | 18 mi |
Moving across the metro or out of state? See all our Denver services or get a quote.
Most Denver jobs don't stop at one service. The crew that rigs a machine out is the crew that manages the move and sets it back down — so you're dealing with one company from the disconnect to the re-level, not three subcontractors pointing at each other.
Machine has to come off the floor, through the door, or onto a pad before it travels? That's the rigging side of the same Denver crew.
industrial rigging in Denver →Presses, compressors, generators, full production lines — disconnected, rigged, hauled, and re-leveled across Denver as one accountable job.
machinery moving in Denver →Machine tools are instruments, not freight. VMCs, lathes, and grinders moved on air-ride and squared back to the builder's spec in Denver.
CNC machine movers in Denver →Moving the whole floor instead of one machine? Phased teardown, sequenced loads, and reinstallation planning for Denver plants.
Denver plant & factory relocation →In Denver we also run riggers, machinery movers, CNC movers, and plant relocation, plus project freight for the jobs we rig — or see every service we offer in Denver.
The same Denver crew also handles millwright services, machinery removal, crane and rigging services, and machinery loading and unloading.
Specialty rigging in Denver: heavy lift rigging, transformer and generator rigging, MRI and medical equipment rigging, lab equipment moving, and printing press moving.
Tell us what's moving and where. We'll route the nearest crew and quote it fast.
Get a Denver Chiller Rigging Quote