Inside a Albuquerque plant there is usually no room for a crane — a roof overhead, live equipment either side, and a floor that has to carry the load the whole way. That is where heavy lift rigging takes over: hydraulic gantries, jacks and cribbing, and skid tracks that move the heaviest pieces in the building without a hook.
Quick answer: Badass Logistics provides heavy lift rigging in Albuquerque, NM and the surrounding metro. We lift, jack, skid, and set heavy equipment with hydraulic gantries, jacking and cribbing, and skid systems — the methods for loads a crane can't reach, can't set up beside, or isn't allowed inside. Our crews work across Albuquerque and nearby New Mexico metros, and moves between facilities run as project freight under the same plan — usually quoted the same day. Call (307) 284-1332.
A crane needs open sky, outrigger space, and ground that can take the bearing. Most heavy equipment in Albuquerque sits where none of that exists — under a bay roof, in a pit, behind a column line, or in a building the load has to roll into. In Albuquerque's energy & industrial plants, the way a heavy piece moves is usually up a few inches, along a planned path, and down onto its set point.
Badass Logistics plans those lifts from the load data out: weight and center of gravity, the lift points the builder allows, floor capacity along the route, and the headroom at every stage. We set hydraulic gantries where the piece has to go up, jack and crib it where it has to come off a truck or a foundation, and skid or roll it where it has to travel. When there is room for a crane, the crane lift and the inside move go into one plan. Jacking and skidding, explained →
The buildings decide the method in Albuquerque. The stock here is a mix of single-storey high-bay semiconductor fabrication buildings in Rio Rancho alongside low-rise research and hangar buildings on the Kirtland Air Force Base and Sandia complex, which is why so many heavy pieces move under a gantry or on skid track rather than on a hook. The heaviest loads in the metro are semiconductor wafer-fabrication tools, cleanroom HVAC and gas-handling systems, precision test and measurement equipment, and aerospace tooling and hangar support equipment — each one planned from its weight, lift points, and the floor under it.
Albuquerque, NM runs on energy & industrial, and almost none of it stays put. Same crews and the same heavy lift rigging standards across the region:
The loads that need these methods are the heaviest and most awkward in the building. Typical Albuquerque heavy lifts include:
That equipment serves Albuquerque's semiconductor and microelectronics fabrication, aerospace and defense engineering, and national laboratory and nuclear research support, where a lift usually happens beside machinery that keeps running. Most of our jacking and gantry work here lands in the Intel semiconductor campus in nearby Rio Rancho, the Sandia National Laboratories and Kirtland Air Force Base research complex on the city's southeast side, and the Mesa del Sol industrial and aerospace development near the Sunport.
Loads lifted and traversed under roofs and inside bays where a crane cannot set up across the Albuquerque metro.
Heavy pieces raised off trailers, foundations, and pits in controlled stages across the Albuquerque metro.
Loads moved along engineered skid tracks or on rollers to the set point across the Albuquerque metro.
Equipment lowered onto anchors, soleplates, and foundations to the layout across the Albuquerque metro.
Plenty of Albuquerque jobs start and finish on one floor. The rest have to travel — to a new building across the metro, a sister plant down I-25, I-40 and I-10, or a facility in another state. We don't hand that part off. It runs as project freight inside the same plan: machines crated or prepped on site, loads sequenced to the rig-out, transport through our licensed broker and carrier partners with dedicated capacity for bigger moves, and our crew waiting at the destination to set it.
Every heavy lift rigging job in Albuquerque, NM is quoted from the actual work, not a rate sheet. These are the things that move the number — send them with your request and you'll get a real quote back fast:
Photos of the equipment, its nameplate, and the path out of the building save a site visit on smaller Albuquerque jobs. For bigger moves we walk both sites before we price anything.
The same Albuquerque crews handle every kind of industrial rigging. If your job looks more like one of these, start here:
Running a trucking fleet out of Albuquerque? See truck dispatch for fleets of 4+ trucks.
Working throughout Albuquerque, NM and the surrounding metro — backed by a nationwide network of 88 locations when a move crosses state lines.
Heavy Lift Rigging throughout Albuquerque and the industrial suburbs around it — the towns below are where the plants, shops and distribution parks actually sit:
| Town | County | From downtown |
|---|---|---|
| Rio Rancho | Sandoval County | 10 mi |
| Santa Fe | Santa Fe County | 58 mi |
| Los Lunas | Valencia County | 20 mi |
| Belen | Valencia County | 30 mi |
| Bernalillo | Sandoval County | 16 mi |
| Grants | Cibola County | 68 mi |
| Edgewood | Santa Fe County | 26 mi |
| Moriarty | Torrance County | 35 mi |
| Enchanted Hills | Sandoval County | 18 mi |
| South Valley | Bernalillo County | 5 mi |
| North Valley | Bernalillo County | 6 mi |
Moving across the metro or out of state? See all our Albuquerque services or get a quote.
Most Albuquerque jobs don't stop at one service. The crew that rigs a machine out is the crew that manages the move and sets it back down — so you're dealing with one company from the disconnect to the re-level, not three subcontractors pointing at each other.
Machine has to come off the floor, through the door, or onto a pad before it travels? That's the rigging side of the same Albuquerque crew.
Albuquerque riggers →Presses, compressors, generators, full production lines — disconnected, rigged, hauled, and re-leveled across Albuquerque as one accountable job.
Albuquerque machinery moving company →Machine tools are instruments, not freight. VMCs, lathes, and grinders moved on air-ride and squared back to the builder's spec in Albuquerque.
Albuquerque CNC movers →Moving the whole floor instead of one machine? Phased teardown, sequenced loads, and reinstallation planning for Albuquerque plants.
plant relocation in Albuquerque →In Albuquerque we also run riggers, machinery movers, CNC movers, and plant relocation, plus project freight for the jobs we rig — or see every service we offer in Albuquerque.
The same Albuquerque crew also handles millwright services, machinery removal, and crane and rigging services.
Tell us what's moving and where. We'll route the nearest crew and quote it fast.
Get a Albuquerque Heavy Lift Quote